Monday, October 7, 2013

At Last, At Last...Copper Sealer Test

At long last I have begun that copper sealer test! Actually, I started it some time ago, but set the washers outside to "weather" in the Florida humidity just before we got a huge wind and rain storm. Needless to say, I didn't anchor the paper I put them on. Nor did I label them. I just labelled their position on the paper. Guess what...the paper got caught by the wind and the washers ended up on the floor. Okay, no one said I was a genius! Anyway...here we go.

I decided to test six pieces of 16 gauge copper wire that I coiled tightly, instead of using washers. Mainly because I work with tightly woven pieces of wire and wanted a little more accuracy of how each sealer worked when wires are closer together. Mind you, this is only a little home test, and the results are to satisfy only basic judgment of how each sealer works. So, if up on your own tests, you get different results, please do not hold me liable. I will plead the fifth!

This time I am testing Renaissance Wax, Maas Commercial Metal Polish Paste, Maas Liquid Metal Polish, Everbrite's ProtectaClear brush on coating, and Everbrite's ProtectaClear Spray. It's all I could handle at one time. Like I said, I used 16 gauge copper, dead soft, 99.9% pure, no coatings.

In the picture to the right, you can see the originals before I did anything to them. The only difference is that I removed the one on the top center. It was one that I was going to do with Maas Commercial using my Dremel. I already had one with Mass Commercial that I used a rag to apply. I figured it was too redundant, so pulled the top center from the test. I am testing only five and I left one in its original condition.

I only coated the spirals on one side and didn't coat the little hooks at the top, wore gloves like a good little girl, and did the test on wax paper. I've had real good luck with sealers not sticking to wax paper, and it protects the surface your working on quite efficiently. Trust me, I have spilled my sealers!

Here are a few things I noticed during the application process:

The Maas products, both the Liquid and the Commercial Paste, were the easiest to use and put quite the shine on the copper, brightening and polishing at the same time without much work at all. I used a non-impregnated polishing towel-like cloth you can get in any cleaning or auto department of your big-box stores.




The Renaissance Wax, see below, went on easy, as well. I did use a Dremel and cloth wheel to apply. The Ren Wax had to sit for a while before I could shine it up. You don't use much and it is dull until polished up. I used the same type towel-like cloth to polish it about 10 minutes later.

 The coil used for the ProtectaClear Spray, on the left with the blurred label, had to be taken outside to spray. I sprayed one side only and the coil seemed to have a lot of little bubbles on it for a while. When I laid the coil down, the sealer leveled out and bubbles disappeared. It takes quite some time to dry and cure. If you do decide to use this product, you can't just spray and go. You have to allow at least a couple of days to complete the drying process, unless you put your sealed item in a 180 degree oven for a while to speed it up.

 With the ProtectaClear brush on, above right, I used a small artist's flat brush and brushed on a fair amount. Again, the same principles apply as with the ProtectaClear Spray. Use wax paper, for sure.

After coating, I placed the coils on another sheet of non-stick paper in a pie tin and placed them outside. In fact, I just did that and it is raining, so the humidity will go up and we should get some cool results I can tell you about in a couple of days. And yes, this time I anchored the pan with something heavy so it won't blow away. Live and learn, right?

One other thing I would like to caution you on when using any type of sealer: wear rubber or nitrile gloves and protective eye-wear and use your sealer in a well-ventilated area. These products are caustic in some cases and may cause injury or sickness if ingested or splashed on the skin. Basically, use some common sense. That's all I ask.

Okay, we are on our way. I will check in with you in a couple of days and let you know what's kicking with these coated coils. Have a good one...and Stay Wired Up!!

6 comments:

  1. Replies
    1. I am actually writing the post now. I will post it tomorrow. You might be surprised!

      Delete
  2. Hi, Gail! Just found your post! Do you remember what the outcome of this test was? Did you have a favorite?

    ReplyDelete
  3. Hi, Margaret! Yes, my favorite was the ProtectaClear from Everbrite Coatings. I have been using this for some time now and am extremely happy with it. The company is family owned and their website is more than willing to help you with any questions. You can read about the results on Wire Rapper at https://ggchambers.com. I should repost that here, too. Thanks!

    ReplyDelete
  4. Thank you, Gail! I'm so glad I found your blog. Great posts!

    ReplyDelete